軟管泵的使用與維護<br />
軟管泵的正常工作對整套鉆探設備的生產效率起著很大的作用。正確維護和使用軟管泵能提高鉆進速度和純鉆進時間，保護孔內清潔，并能將井壁坍和卡鉆事故減至小。因此我們應當做好泵的使用，維護和保養工作。為保護軟管泵的壽命及其正常工作，必須從包裝運輸保存開始，直至安裝使用和維護保養都精心注意。<br />
1、軟管泵在開啟前的維護與保養，在軟管泵開動前應對軟管泵系統作檢查；對液力端的整個循環系統作仔細檢查；<br />
2、軟管泵在運轉過程中的使用與維護，檢查各運動件的潤滑情況；要密切注意泥漿質量；注意壓力表，閥工作是否正常；曲軸箱內的油溫及缸套活塞副的溫度不得過高。<br />！

首先我們先介紹一下軟管泵，軟管泵又稱蠕動泵。為了泵體污染流體或流體污染泵體的危險性，整個泵的裝置中只有軟管與介質接觸。在一般場合下，軟管泵使用的都是天然橡膠的軟管。內層和外層都是完整光滑的天然橡膠，其目的是很強防磨損。適用于腐蝕性不高但磨損性很大的如泥漿以及無機物等等介質。而且一般適用于脂肪、油類或油脂的介質，以及有機化學物質。內層是橡膠，而外層是天然橡膠或者是復合橡膠。

First of all, lets introduce the hose pump, which is also called peristaltic pump. In order to eliminate the danger of the pump body contaminating the fluid or the fluid contaminating the pump body, only the hose in contact with the medium in the entire pump device. In general, hose pumps use natural rubber hoses. The inner and outer layers are completely smooth natural rubber, the purpose of which is to prevent abrasion. It is suitable for mediums that are not corrosive but very abrasive, such as mud and inorganic substances. And generally suitable for fats, oils or oils, and organic chemicals. The inner layer is rubber, while the outer layer is natural rubber or composite rubber.

 

眾所周知軟管泵在運行時，是通過一根U型附有彈性的橡膠軟管來完成輸送。今天小編需要強調的是，軟管存放時間不宜過長，一般以一年為限。在停工期間，對裝有軟管的泵，若長期不用，每隔一個月需轉動泵一次。以免壓輥長時間壓在泵管的某一處，減弱管子回彈性，影響其流量的輸送。

It is well known that when the hose pump is running, it is conveyed through a U-shaped rubber hose with elasticity. Today the editor needs to emphasize that the storage time of the hose should not be too long, and it is generally limited to one year. During the shutdown period, if the pump is equipped with a hose, if it is not used for a long time, the pump needs to be rotated every other month. So as not to press the roller for a long time at a certain position of the pump tube, it will weaken the resilience of the tube and affect its flow rate.